Replacement UPVC Door Handles

You can find the ideal handle for your door, whether you're replacing your existing handles or adding security. These upvc handles are easy to fit and comply with the required 92mm centres for multipoint locks.

The backplate's fixing centre as well as the keyhole/lever dimensions are the most important measurements. Compare these measurements to your existing measurements prior to ordering.

Lever/Pad

Lever pad door handles are made up of an elongated lever handle on one side and a paddle shaped handle on the other. They are intended for use with key wind locks. However, they can be fitted to multipoint split spindle door locks.

Our range of upvc handles lever pads are available in a wide range of finishes. They will be listed in the drop down list once you have found the right handle for your door. Not all styles of handles are available in every finish though and you should always look over the sizes and technical drawings for the specific product you are looking to ensure that you can get the correct size and fit.

When you are choosing the new set of upvc lever pad door handles it is crucial to make sure that they match the PZ (distance between the handle spindle and the center of the hole for the cylinder) of your current multipoint door locks, as these need to be in the same line to allow doors to remain locked, either from the inside or the outside. The handles we offer are designed to work with the majority of conventional cylinder locks, however it is advisable to double glazing door handles-check before purchasing.

If you are looking to upgrade to dual spindle levers, you will need to remove the existing handles and disassemble the lock case. This will require an additional split cylinder inline. You can purchase these separately. We have included a diagram of the technical aspects in the images of each product.

After you have removed the screws that are holding your existing door handle it is recommended to loosen them, and then inspect the mechanism to determine how it's performing. You may have to loosen the screws further if they are not tight. After that, you can remove the old handle and spindle and put in your new door handle made of upvc. Before you screw the handle into the frame, it is a good idea to make sure it is in the correct position. You can do this by placing your finger into the gap between the door frame and the handle to make sure that it is in a level position.

Lever/Lever

The lever handles on doors are used to operate a multi-point lock that uses the Euro cylinder. They can be found on a variety of double glazing window handles upvc doors, as well as on some aluminium and wooden doors. They are available in two forms, having a lever on the interior and a paddle on the outside. Sprung - they have a spring cassette fitted inside the backplate to move the handle lever to a horizontal position. Non-sprung: These do NOT have a mechanism to spring the handle lever into a horizontal position.

To fix a door handle that is sagging, you will need to locate the detent access hole or pin, which is usually a small round or rectangle shaped hole or protruding pin that is located on the opposite side of the handle base plate. Once located you can loosen the set screw using a screwdriver and remove it to allow the lever and return it to the horizontal position.

After the handle is positioned horizontally, Replace Window Handles you can install the screws. Close them to ensure that the handle stays connected to the base plate. It is also advisable to apply an adhesive that locks the screw threads to increase the grip and stop them from becoming loose over time.

There are a variety of reasons why door handles of levers drop. The most common cause is that the fixings aren't tight, causing the lever bearing to get tangled up against the door. It is also possible that the levers may not have been operated at the correct angle, which compresses the latch mechanism, preventing it from fully springing into motion.

Another reason is that the sprung lever is not working properly. This is usually due to the spring not being in the correct position within the backplate. The simplest way to check this is to operate the handle and see whether it returns to its horizontal position.

If the door handles aren't tight, it is crucial to find the issue quickly, since this can lead to excessive wear on the screws and possibly to the handle falling off of the base plate. It is recommended to tighten all loose screws regularly in order to prevent them from loosening.

Lever/Snib

These upvc door handles are also known as 'Snib' handles and have a snib lever towards the top of the lever that you can push down to lock your door if you don't have the fake lock. These door handles are fitted with the Fullex lock 68PZ. (68mm between the spindle and lock centre). We also have a range of other door handles with 68PZ from manufacturers like Ferco and Fab & Fix.

Changing your door handle is a cost-effective method to upgrade your home, whether replacing existing handles or fitting new ones on doors you've built in your house. There are a variety of styles available for door replace window handles (visit the next page) made of upvc, including the traditional lever on backplate. Other choices include straight or curved short latches as well as Dummy knobs for multi-point locks. These are ideal for French doors.

Rose door handles are oval or circular versions of backplate lever handles. These types of door handles come with a lever or knob on a backplate that sits behind the lever or knob and is often referred to as a rosette, although certain backplates can be removed to allow for concealed fixing.

These handles are available in various finishes, including chrome and coloured finishes to be matched to your door and hardware such as knobs, hinges and bolts. Some handles are supplied with grub screws that help firmly attach the knob or lever to the spindle. Some handles come with bathroom spindles that can be used for bathroom locks. They also have a thumbturn release mechanism, and can be used on doors for bathrooms.

Mortise

The tubular latch is the most likely to be the cause in the event that your door handle is slammed shut. There may be a few factors that could cause this, the most common being the simple lack of lubrication on the latch plate. It is possible to fix this issue by opening the door, spraying lubricant on the handle and locking. Or, it could be that the latch plate has become separated from the backplate. This could be more complicated and will require a specialist to fix it.

A multipoint handle system is the best solution for stuck door handles. These handles are attached to the faceplate and operated with a key or thumb turn knob that triggers the cam that locks the deadbolt. The handles are available in a variety of sizes to suit different types of uPVC doors and come in an array of attractive finishes that complement the existing hardware. The handles can be purchased online or through an authorized locksmith in your area. They are simple to install, with clear instructions.

You'll need to know your cylinder's PZ size in order to select the right replacement upvc door handles handle set. This is the distance from the edge of the inner frame of the door to the center point of the handle hole in millimetres. You should also determine if the door is hook locks or a mortise lock. Once you know these measurements, the easiest way to find the correct handles is to search by brand option on the website. This will narrow down your options and you can then choose the right size from the list.

A typical handle set comes with the handle unit, a pair of different length screws, drill guides and installation instructions. Smarter versions, such as the Igloohome Smart Mortise 2+ include a mortice lock with keys. These are more complex models and are ideal to professional installers or adept DIYers. Some handle sets have an array of other accessories, like weather strips, that can be used to improve the appearance of the door.