Why Your Rolls Royce Phantom Key Fob Isn't Locking Or Unlocking

There's nothing on the market that can match the Rolls Royce Ghost Key [Http://Single-Life.Co.Kr]-Royce Phantom for sheer opulence. It's higher and heavier than most SUVs, oozes luxurious inside and Rolls Royce Ghost Key out, and is a breeze to customize for its well-heeled owners.

A malfunctioning key fob could cause problems in operating your Phantom. There are steps you can follow to fix the issue.

Battery Replacement

The key fob is powered by an in-container battery. The remote key won't function when the battery inside is dead. A dead battery inside the key is the most typical reason for a Rolls-Royce Phantom remote key not locking or unlocking. It is also possible that the key fob will not function as it should when the battery terminals or ground connection are corroded.

The procedure of replacing the key is fairly simple. Make sure the key is dry and clean. You don't want any moisture to the new battery. Press the release button on the side fob to release the mechanical keys. Then you will need a screwdriver to remove the cover of the key fob and remove the battery. Replace the battery with a new one. Make sure that the positive (+) face is upward. Snap the cover in place.

The Phantom key rolls royce fob features rubber seals that block water from getting to the electronic chip inside. If the key is submerged for an extended time in water, such as in an swimming pool or ocean the chip could be damaged. A short exposure to water splashes is fine, but prolonged submersion in water can cause the circuit board to fail. In this case, replacing the battery is the most effective solution.

Water Damage

A key fob may be waterproof however a dip in the pool or the washing machine can cause problems. The circuit board may be shorted, and rust or corrosion may set in faster. In extreme instances batteries can explode or even die.

Taking the fob immediately out of the water can help prevent this kind of damage however, you should think about replacing the battery. Use the same kind and size of button cell batteries as the original. Then, thoroughly clean the electronic component using alcohol or an electronic cleaner before installing it.

After replacing the battery, turn the Phantom on and press each button. If none work it's time to take it apart and dry it out before you can use it again.

The most effective way to achieve this is to put the fob inside the container of rice. The rice will absorb any moisture that could have made it into the fob. You can also blow dry the circuit board and the fob's insides using an electric hair dryer or heat gun. Be sure to avoid using a microwave as the circuitry on the key fob's board could be damaged. After it's dried, reassemble the fob and test it again.

Diagnostics of a fault

It is a traumatic experience to lose your keys. In the ideal case you'll find them exactly where you left (Parent Logic insists they always appear in "the last place you have looked" however this isn't something you can debate). If your key fob does not react to your commands, it's not as simple.

The first step is to check the battery in the coin - dead batteries are the primary cause of remote key fobs that fail. A dying battery will display signs of degradation such as a decreased range until it ceases to function. Replace the battery with a new one that is identical in size, voltage and specification. This is crucial to avoid damaging your electronics.

The chip inside the key fob might be damaged. It can happen if drop the key fob on the floor or expose it to water. In this scenario, you must remove the chip from the key fob and clean it using isopropyl or electronic cleaner.

It is also possible that the Phantom's receiver is having issues. This could be caused by various causes, including signal interference as well as a dead 12 volt battery, or a unpaired key that requires changing the program.

Reprogramming

If your rolls royce cullinan key Royce Phantom remote key fob suddenly stops working there could be the result of a problem with your receiver module. It is the small unit inside the boot that receives radio signals from the remote key fobs. If the key fob stops working after you dropped it on the floor or if one of the keys isn't responding to your commands, it may be time to visit an auto locksmith to re-programme it.

The rubber seals on the key fob stop water from damaging electronic chips. However long exposure to water may damage the seals. Immersing a key in an in-ground pool or bath could cause damage. However a drop of ocean water on the beach is more damaging because of the high conductive nature saltwater.

If your Phantom key of rolls royce fob has suffered water damage, you are able to reset it using these steps:

Close all doors, excluding the driver's. Finally, take the car into the garage. Then, insert your car key into the ignition and switch it to the "ON" position. Certain models will sound an alarm when you enter program mode. Press and hold the "UNLOCK", "PANIC", and "PANIC" buttons for a few seconds before being released. The car should then sound to confirm that it's in program mode and that the key fob has successfully connected to your vehicle.